How Do You Hook Up A Drill Battery To A Power Wheels?
We may earn commission from links on this page at no extra cost to you. We only recommend products we back!
Power Wheels cars are an exciting and fun way to explore. But after a few months of use, the toy cars slow down a bit. Then your kids will not like its slow speed, and they will not want to play with it.
Because kids will want more exciting rides as they get to grow up. Then you will want to add a new battery to increase the car’s speed. So, how do you hook up a drill battery to a Power Wheel?
How Do You Hook Up a Drill Battery to a Power Wheels?
The power wheels drill conversion is a technique for converting old, dead power tools’ batteries into usable ones. You may put a new battery into a power wheel and significantly enhance its speed with just a few simple actions that any DIY can perform.

Aside from saving money, this method is an environmentally responsible process of reusing old power tool batteries. Because this battery trash is dangerous and pollutes dumps. In some manner, you are assisting in reducing the number of lithium batteries thrown away in landfills.
How to Hook Up a Drill Battery to a Power Wheels?
Before adding a drill battery to your child’s power wheels, you need to collect some parts and equipment. Before you begin your entire conversion process, ensure you have collected all of the following components and equipment.
Parts:
- A Hercules battery adapter
- 6v or 12-volt power wheel
- A Battery charger
- 30-amp inline fuse
- A Lithium tool battery
Tools:
- Wire stripper
- A Screwdriver
- Soldering iron
- A Wire crimper
- Electrical tape
Let’s get started on the step-by-step guide now.
Step 1: Find the Stock Battery
First, you need to find the battery in the Power Wheels car. Typically, a power wheel can have a battery under the hood or under the seat.
Now remove the battery from your child’s toy car. It would be best if you found out how many volts were in your child’s Power Wheels car battery. Now make sure you know how many volts of battery you need before choosing a new battery.
Read More: How To Tell If Power Wheels Battery Is Charging?
Step 2: Adjust the Stock and Drill Battery
Now all you have to do is cut off the two wires attached to the battery. Because you now need a connector plug to connect the wires. You have to remember that you can’t use stock batteries if you do this.
Now it’s time to connect the stock battery connector to the 3D printed default battery connector. To do so, connect the negative (-) cable to another black wire.
All you have to do now is twist together the wires and apply electrical tape. You may proceed with crimpers after completing this task.
Also, you must connect them to the positive cable (red), but place a 30-amp inline fuse in between. This fuse will prevent your motor from receiving too much power. The fuse will break if too much power is drawn from the motor, causing it to shut down automatically.
Read More: Can You Put A Remote Control On Power Wheels?
Step 3: Attaching the Drill Battery
All of the connections to the battery are now completed. It’s time to join everything together now. However, first make sure that the fuse is in the correct wire using the velcro on the back of the battery adapter holder.
We also recommend that you purchase an electric speed controller kit if you’re going to use one.
So that you can regulate the amount of energy going into the wheel and the baby may get a break on the new energy. Now connect the drill battery to your power wheels in an appropriate way.
Step 4: Check the Toy Car
Once you’ve installed the race drill batteries in your child’s power wheels, you may test them and the motor by pressing on the gas pedals and watching the back wheel spin.
Take a good look at it to see if the wheels are turning correctly. Hopefully, you will notice a significant change from before. Check the motor thoroughly to verify that the motor has gained strength.
Overall, you will notice a considerable difference in the quality of your child’s toy car compared to the stock batteries.
Because of its lighter weight, this lithium tool battery pack speeds up the power wheels considerably. In general, these lithium tool batteries extend battery life far more effectively than 12v or 6v batteries utilized in power wheels.
Read More: How To Modify Power Wheels To Go Faster?
Step 5: Final Stage
If you connect each component in the car correctly, the test should pass and the power wheels will run well. Now it’s time to inspect all of the cables to verify that they’re safe. If you soldered all of the wires together, you’d be most effective in your job.
The wires would be safe, the wires wouldn’t hang, and there would be no risk of tearing if you soldered. You can now use a multimeter to verify the battery’s voltage. Make sure that the vehicle’s battery voltage is suitable for it.
Now you switch everything off in the vehicle and don’t forget to clean it thoroughly. Once the power wheels are cleaned, put everything back. Otherwise, certain components may be lost and you will not be able to locate what you need.
After you’ve installed a new drill battery, charge your car’s new battery. A replacement ride-on charger is available if you don’t have a charger. However, it’s preferable if you charge the battery with a manufacturer’s charger.
Note that: Adding an inline fuse holder is required to replace batteries. This change is straightforward with a power wheels battery adapter, which may cause your child’s power wheel to go 50% faster.
Be sure you have the necessary toolkit, especially the inline fuse. Skipping the fuse is not an option. If you’re unsure about any of them, get in touch with someone who knows what they’re doing.
FAQs
1. Is It Possible To Add Two Battery Packs To The Power Wheel?
Yes. Of course, it can be done. If you do this, it will double your child’s driving time and, if done correctly, will increase the speed of the toy car.
However, for this, you must connect the battery in parallel. If you connect the batteries in parallel, the motors will get 36v to 40v power.
2. Is It Safe To Upgrade Power Wheels Car Batteries?
Yes. Until you’ve identified and resolved any issues that may occur. A safe outcome necessitates a minimal amount of electrical knowledge and battery replacement.
This includes locating the right connecting points, preparing a fuse, and securely fastening the connections.
On the other hand, you must select the battery that matches the power wheels. For example, if your car has a 6V volt battery, you can upgrade it to 12 volts. Of course, you don’t want to convert it to a 24-volt battery.
3. Which Battery Can You Choose To Upgrade The Power Wheels Battery?
There are two most common types of batteries you can choose from, sealed lead-acid batteries or lithium batteries.
You may have some concerns about undertaking this job, but it is a gratifying project that will save you a lot of money. When you’re having trouble with any parts, get in touch with an expert.
Final Thoughts
We hope that all the information in this article will be helpful to your drill conversion project. As you add more voltage to the toy car, the car’s speed will increase. This is why you must keep your child’s safety in mind.