How To Modify Power Wheels To Go Faster?
We may earn commission from links on this page at no extra cost to you. We only recommend products we back!
The power wheels are a great toy for kids, but they can be frustrating to the parents whose kids just want to go faster.
The good news is that there are some easy modifications you can do to modify your power wheel and make it go faster. But be aware of the risk of losing control when you are going at those speeds.

Can I Modify A Power Wheels?
Yes, there are a lot of different ways to modify power wheels. The first thing you can do is get higher quality, longer-lasting batteries for your electric car. This will allow it to go faster because the battery doesn’t have as much draw on the system with better quality and more durable batteries.
You should also invest in some new wheel bearings, which makes everything smoother while driving over rough terrain or pavement that has been damaged from years of wear-and-tear due to normal use by cars going through the same area every single day.
Read More: Power Wheels For 5-10 Year Olds
If you want something less expensive and something that could still make your vehicle perform better than before, then I recommend installing larger diameter tires onto your power wheels. This does not cost too much money but it dramatically increases the speed that you can go.
For most of the modifications, you will need to remove the plastic casing on your power wheels. The reason for this is because some parts are held in place by screws that have been drilled into those pieces.
These screws may not allow enough room for a new component or they could damage it when tightened down too much. There are basically two ways to do this- one involves taking off all four bolts with an Allen wrench while the other just takes out two bolts at a time so that there’s less chance of dropping anything inside.
After removing everything from underneath, get yourself something like WD40 or lithium grease so as to lubricate anything metal before putting it back together again.
How to modify power wheels to go faster, step by step
Step by Step Instructions for Modifying Power Wheels to Go Faster:
- Installing a New Motor
- Installing a new controller
- Installing a new battery
Installing A New Motor:
How fast your modified power wheels can go is determined not only by the type of motor you choose but also on whether or not it’s geared. There are two main types of motors that are geared or ungeared.
If the motor is not equipped with a gear, it will spin at full speed no matter what you do to it. This means that any modification done to this type of motor will have very little effect on how fast your power wheels can go. It also doesn’t take into account things like drag and torque.
Read More: Best 24 Volt Battery Powered Ride On Toys
If the motor is geared, it will only spin at a certain speed. However, gears can make your power wheels go faster or slower depending on which gear you choose to use. If you’re looking for more of a speedy ride, then an ungeared type of motor with gears might be right for you. However if you want to take it a bit slower, then you’ll want to gear your motor.
The ungeared type of motor has no gears and is much simpler for beginners because they do not need to worry about gearing.
Geared motors are great if you’re looking for more speed but still require some patience in order to figure out how to get it to work well.
The ungeared type of motor is also the cheapest and easiest option. You’ll need a gearbox, belt, sprocket, bearing and wire.
Geared motors are more expensive but do offer speedier options that beginners can still use with some patience.
Motors without gears have two wires coming out of them, while geared motors have four. The ungeared motor has a one-way clutch that helps it move more smoothly and requires less power consumption.
Geared motors are better for harsher terrains because they can handle the torque from stepper hills. They also use more battery power than an ungeared type motor when climbing steep inclines. Geared motors also need a gearbox.
Read More: Electric Cars For 10 Year Olds To Drive
The best type of motor for beginners is the ungeared type because it’s cheap and simple to use, but not very powerful. Experienced drivers might prefer geared motors because they have more power and are more durable.
To install the new motor, you first have to remove all of the bolts that are holding it in place. Be sure not to drop anything inside where you cannot see because there could be a lot of little pieces underneath. Then spray some WD40 or lithium grease on any metal surface before putting it back together again so as to prevent things from getting stuck.
Your power wheels can go faster by installing an upgraded and more powerful electric motor instead of using the original one. Which is usually less powerful than what’s available nowadays for purchase at many stores like Toys”R”Us and WalMart for example.
Read More: Best 2 Seater Ride On Car With Parental Remote Control
This process involves removing four screws with an Allen wrench while loosening two other ones every time until everything comes out from the axle which is the center of rotation. Don’t forget to put some WD40 or lithium grease on any metal surface before putting it back together again, this will prevent things from getting stuck and make your connection last longer.
Installing a new battery:
You should pick a battery that fits your needs. So if you’re going to be driving through rough terrain, it’s best to get one with more amp hours.
If the power wheel has an on/off switch then make sure the wire from the battery is long enough. The wire for 12 volt batteries can be up to 50 feet in length.
If it doesn’t have an on/off switch then you’ll need to get a power cut-off switch that’s designed for 12 volt batteries, but make sure the wire is long enough as well because they too can be up to 50 feet in length
Once the battery is hooked up, use pliers to tighten the nut on the positive and negative terminals.
To make sure you’re not overcharging your battery, put it in a well ventilated area that’s at least 12 inches off of the ground.
Installing a new controller:
You can find a controller from an online store or you could purchase one from a local hobby shop.
The easiest way to install the controller is by using double sided tape but make sure it’s not so sticky that it will rip apart your power wheels when you remove the old and new controllers later on, as this would be very difficult to fix.
Connect the black wire to the negative terminal on your battery and then connect the red wire to the positive terminal.
You’ll want to use wire connectors for the final connection.
Connect one end of a long piece of wire in your power wheels, using the connector and then connect it with another set up on your controller which should look something like this:
* Black wire connector goes on the negative terminal of your battery.
* Red wire connector to positive terminals of your power steel.
* Connect a long piece of extension wire, about 18 inches and if you need any help figuring out where it should go in your car or how to make sure it doesn’t become disconnected while riding, consult the manual.
* All the wires should be connected together in a chain, with one end of the extension wire on your power steel and the other end attached to your controller.
Remember to use connectors when connecting all these pieces or it can come apart while you’re riding.
Now that everything is set up correctly, turn on your power steel by pressing the “on” button.
After you have turned it on, press and hold down the acceleration pedal in your car. The power will kick in as soon as the motor starts to turn. So release the accelerator after that happens for a little bit of time until it begins going faster.
Final Verdict
In this article, we’ve shared some of the ways to get your power wheels going faster. Hopefully, these ideas will help you choose a solution that works for your needs and budget. We hope after reading our post, you have an idea of what kind of modifications might work best for you. If so, be sure to share how they worked out in the comments below! Happy modifying!